CEMS RFQ - Contact Us | Universal Analyzers

All fields marked with (*) are required

CONTACT INFORMATION

First Name*

Last Name*

Company*

Mailing Address

City

State

Zip

Country

Phone*

Mobile

Email Address*

MONITORING POINT INFORMATION

Application Description*

What type of combustion unit is used (boiler, turbine, engine, other)?

What type of fuel is burned (coal, oil, gas, refuse)?

Does the monitoring point have an ESP or Baghouse?

YesNo

If yes is monitoring point Upstream or Downstream of ESP or Baghouse?

UpstreamDownstream

Is the monitoring point Downstream of wet scrubber?

YesNo

Is the monitoring point Downstream of ammonia injection?

YesNo

STACK GAS DATA - GAS COMPOSITION

SO2 - Units

Normal

Maximum

CO2 - Units

Normal

Maximum

H2O - Units

Normal

Maximum

N2 - Units

Normal

Maximum

O2 - Units

Normal

Maximum

NO - Units

Normal

Maximum

NO2 - Units

Normal

Maximum

CO - Units

Normal

Maximum

Other unusual components or contaminants (include particulate size and volume)

PROCESS PARAMETERS

Temperature (Min)

Temperature (Max)

Temperature (Typical)

Temperature (Units)

Pressure (Min)

Pressure (Max)

Pressure (Typical)

Pressure (Units)

Flow (Min)

Flow (Max)

Flow (Typical)

Flow (Units)

Velocity (Min)

Velocity (Max)

Velocity (Typical)

Velocity (Units)

Particulates (Min)

Particulates (Max)

Particulates (Typical)

Particulates (Units)

Phase

If vapor phase, dew point

Other Data (viscosity, unusual surges, contaminants)

psi (gauge)

Sample boiling point (°F/°C at atm pressure)

Are there likely to be any mists, etc in the sample?

STACK PHYSICAL DATA - CEMS SAMPLE PROBE

Sample point elevation from grade (ft/m)

Inside diameter of stack at sample point (in/mm) (Fig #1 - Item C)

Outside diameter of stack at sample point (in/mm)

Flange projection from stack at sample point (in/mm) *Note: 6-8in is recommended. (Fig #1 - Item B)

Flange Size

Bolt Pattern: Do the holes straddle top dead center - if no please email sketch. (Figure #2 above)

YesNo

STACK PHYSICAL DATA - CEMS VELOCITY PROBE

Velocity probe elevation from grade (ft/m)

Inside diameter of stack velocity probe (in/mm)

Outside diameter of stack velocity probe (in/mm)

Flange projection from stack at sample point (in/mm) *Note: 6-8in is recommended.

Flange size

Bolt Pattern: Do the holes straddle top dead center - if no please email sketch. (Figure #2 above)

YesNo

Is the velocity probe located 8 stack diameters upstream and 2 stack diameters downstream from any flow disturbance? (Please email velocity profile if available)

YesNo

Does the stack have an outer shell?

YesNo

If yes, please provide diameter (ft/m)

ANALYZER LOCATION - AMBIENT CONDITIONS

Shelter interior temperature Min (°F/°C)

Shelter interior temperature Max (°F/°C)

Shelter exterior temperature Min (°F/°C)

Shelter exterior temperature Max (°F/°C)

Average barometric pressure

Pressure units

mm HgkPain Hg

Special weather conditions (eg: Sandstorms, Hurricanes, etc.)

Plant elevation from sea level (ft/m)

ANALYZER LOCATION - AREA CLASSIFICATION

Analyzer

Non-Hazardous Classification
Hazardous Area Classification

If hazardous area, please indicate classification (C1D2, Zone 2, etc.)

Sample Point

Non-Hazardous Classification
Hazardous Area Classification

If hazardous area, please indicate classification (C1D2, Zone 2, etc.)

Shelter Interior

Non-Hazardous Classification
Hazardous Area Classification

If hazardous area, please indicate classification (C1D2, Zone 2, etc.)

Shelter Exterior

Non-Hazardous Classification
Hazardous Area Classification

If hazardous area, please indicate classification (C1D2, Zone 2, etc.)

HEATED SAMPLE LINE

Estimated sample line length (in/cm)

UTILITIES AVAILABLE

Power available for shelter

Power available for probe & SCS

Steam (psi/gauge)

Nitrogen (psi/gauge)

Instrument Air (psi/gauge)

Instrument Air Temperature (°F/°C)

Clear Water (psi/gauge)

UPS Available?

YesNo

Other? (Please specify)

Check box to be added to our mailing list

CONTACT US

CEMS Application RFQ